LINE ARRAY

M-F3


Small Size, High SPL 2.1 Active Array system

M-F3 is a compact and modular active all-in one array system which is composed of a double 10" active sub, a four-channel amplifier & single processor and two passive full range speakers. Although being of small size, this system provides high power output by adopting line array principles. Single speaker can be used independently to support the whole system and a combination of the speakers can also be used as a line array system. With built-in DSP, Feedback destroy switch, frequency knob and also high shelf knob, the amplifier has greatly facilitated the system's ability to conduct tuning and feedback suppression in complex environments.



 Small size, high SPL

M-F3 is a compact and lightweight array speaker that has the same frontal measurements as a sheet of A4 paper and a weight of only 8 kg. Still, one unit of this compact array delivers 119db SPL continuously and 126db peak SPL. Advanced cooling and venting measures keep power compression at a minimum.



Amplifier & Signal processor

With built-in DSP, feedback destroy and high shelf filter, the Class-D amplifier has the ability to conduct tuning and feedback suppression in complex environments.




Line source

Each unit is already a line array in itself with very wide horizontal and precisely controlled vertical dispersion.




Versatile mounting

Due to its light weight, 14 rigging points and a supporting base, M-F3 can be set up in flying, wall mounting or ground stacking mode to meet the demands of various application environments.






SPECIFICATIONS


Model NameM-F3
Type: 3" bassreflex
Frequency Range (-6dB) :120 Hz-18 KHz
Power Handling(RMS):200 W
Sensitivity(1W / 1M):100 dB
Max. SPL (1m) :126 dB
Impedance:
Dispersion(H × V):120° × 16°
transducer MF:8 × 2.8” Neodymium Magnet with cooling module, 0.75”Voice Coil
transducer HF:7× 1”Neodymium Magnet, 1”Voice Coil
Cabinet / Paint:12mm MDF, white PU texture paint
Dimensions (W × H × D) :210 × 296 × 233 mm
Weight:5.5Kg + 5.5Kg
M-F3 SUB
Type:10” V construction, bandpass
Frequency Range (-6dB) :40 Hz - 250 Hz
Power Handling(RMS):400 W
Sensitivity(1W / 1M):98 dB
Max. SPL (1m) :129 dB
Impedance:
transducer LF:2 × 10”Ferrite Magnet, 2”Voice Coil
Power Ampilifer Type:Class D amplifier, SMPS
Signal Processing:DSP, 48 kHz, 24 bits
Protection:Multiple limiter, short circuit, overheating
Controls:On / Off switch, sub level, Low pass frequency knob, 0°- 180° phase switch
Indicators:On, signal, limit, protect
Line Input / Output:input XLR/ Router-output XLR
Cabinet / Paint:15 mm plywood, black polyurea paint
Dimensions (W × H × D) :400 × 500 × 510 mm
Weight:25 Kg
M-F3 AMP
Power Ampilifer Type:Class D amplifier, SMPS
Power Handling(RMS):(200 W + 200 W) × 2
Input Sensitivity:- 4 dBV
Signal Processing:DSP, 48 kHz, 24 bits
Protection:Multiple limiter, short circuit, overheating
Controls:On / Off switch, Main level, Full/ SAT switch, Feedback destroy switch, Feedback destroy knob, High shelf knob
Indicators:On, signal, limit, protect
Line Input / Output:input XLR / Router-output XLR, speaker out Neutrik NL-4
Dimensions (W × H × D) :483 × 66 × 347 mm
Weight:6.5 Kg






DIAGRAM


ACCESSORIES

3/8"Adaptor
SPS-20
M-F3 LC
SMB
CM





PICTURE





DOWNLOAD